System
-----------------------
K3b Version: 1.0.4

KDE Version: 3.5.8
QT Version: 3.3.7
Kernel: 2.6.22-14-generic
Devices
-----------------------
_NEC DVD_RW ND-4570A 1.02 (/dev/hda, ) [CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL] [DVD-ROM, DVD-R Sequential, DVD-R Dual Layer Sequential, DVD-RAM, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96R, RAW/R96R, Ограниченная перезапись]

Used versions
-----------------------
cdrecord: 1.1.6

cdrecord command:
-----------------------
/usr/bin/wodim -v gracetime=2 dev=/dev/hda speed=10 -tao driveropts=burnfree -overburn blank=all -force

cdrecord
-----------------------
/usr/bin/wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.

scsidev: '/dev/hda'
devname: '/dev/hda'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.6
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 1 = CD-ROM
Driveropts: 'burnfree'
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : '_NEC '
Identification : 'DVD_RW ND-4570A '
Revision : '1.02'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x000A (CD-RW)
Profile: 0x002B (DVD+R/DL)
Profile: 0x001B (DVD+R)
Profile: 0x001A (DVD+RW)
Profile: 0x0015 (DVD-R/DL sequential recording)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x0012 (DVD-RAM)
Profile: 0x0011 (DVD-R sequential recording)
Profile: 0x0010 (DVD-ROM)
Profile: 0x000A (CD-RW) (current)
Profile: 0x0009 (CD-R)
Profile: 0x0008 (CD-ROM) (current)
Profile: 0x0002 (Removable disk)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R
Drive buf size : 1343488 = 1312 KB
Speed set to 1764 KB/s
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 2
Reference speed: 6
Is not unrestricted
Is erasable
Disk sub type: High speed Rewritable (CAV) media (1)
ATIP start of lead in: -12374 (97:17/01)
ATIP start of lead out: 359849 (79:59/74)
1T speed low: 4 1T speed high: 10
2T speed low: 2 2T speed high: 10
power mult factor: 2 6
recommended erase/write power: 5
A1 values: 24 2C DC
A2 values: 14 A4 4A
A3 values: 02 D2 80
Disk type: Phase change
Manuf. index: 69
Manufacturer: Moser Baer India Limited
Manufacturer is guessed because of the orange forum embargo.
The orange forum likes to get money for recent information.
The information for this media may not be correct.
Waiting for drive to calm down.
Starting to write CD/DVD at speed 10.0 in real force BLANK mode for single session.
Last chance to quit, starting real write in 2 seconds.
1 seconds.
0 seconds. Operation starts.
Errno: 0 (Success), blank unit scsi sendcmd: no error
CDB: A1 00 00 00 00 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 03 00 00 00 00 0A 00 00 00 00 73 03 00 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x73 Qual 0x03 (power calibration area error) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 30.401s timeout 9600s
Starting to write CD/DVD at speed 10.0 in real force BLANK mode for single session.
No chance to quit anymore. Operation starts.
Performing OPC...
/usr/bin/wodim: OPC failed.
Blanking entire disk
Errno: 0 (Success), blank unit scsi sendcmd: no error
CDB: A1 00 00 00 00 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 03 00 00 00 00 0A 00 00 00 00 73 03 00 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x73 Qual 0x03 (power calibration area error) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 30.394s timeout 9600s
/usr/bin/wodim: Cannot blank disk, aborting.